TM 5-3810-300-24&P-3
Subject
Section
Subject
Section
Option plate .................................................................... *
Starting motor..............................................................7.3
Overhaul specifications (see specific part)
Stopping--engine.......................................................13.1
Storage--engine ........................................................15.3
P
Storage battery............................................................7.2
Pan--oil ....................................................................... 4.7
Strainer--fuel oil...........................................................2.3
Panel--instrument ....................................................... 7.4
Support--blower drive gear.......................................1.7.6
Piston rings................................................................. 1.6
Switch--solenoid.......................................................7.3.1
Pistons--cross head.................................................... 1.6
Switch--starting ...........................................................7.4
Plate--cylinder block end ......................................... 1.1.1
Systems:
Plate--option ................................................................... *
Air intake..................................................................3
Polarizing generator (battery charging) ...................... 7.1
Cooling.....................................................................5
Pre ignition--effects of ................................................ 2.0
Electrical ..................................................................7
Preventive maintenance ........................................... 15.1
Exhaust....................................................................6
Procedures--general....................................................... *
Fuel..........................................................................2
Protective systems-engine ...................................... 7.4.1
Lubrication ...............................................................4
Pulley--crankshaft.................................................... 1.3.7
Shutdown--air ....................................................7.4.1
Pump:
Ventilating .............................................................4.8
Fuel oil ................................................................. 2.2
T
Lubricating oil ....................................................... 4.1
Water ................................................................... 5.1
Tachometer drive ........................................................7.4
Push rod .................................................................. 1.2.1
Temperature gage capillary tube ................................7.0
Test--dynamometer................................................13.2.1
R
Test--fuel flow .............................................................2.0
Radiator ...................................................................... 5.3
Test fixture--injector ....................................................2.0
Radiator cooling system ................................................ 5
Test report ..............................................................13.2.1
Regulations--exhaust emission ................................... 14
Testing injector--needle valve ..................................2.1.1
Regulator--Voltage .................................................. 7.1.1
Thermostat ...............................................................5.2.1
Regulator--oil pressure ............................................ 4.1.1
Thrust washers--crankshaft .....................................1.3.4
Restoring engine to service ...................................... 15.3
Timing:
Rings--piston .............................................................. 1.6
Blower...................................................................3.4
Rocker arms ............................................................ 1.2.1
Crankshaft gear .................................................1.7.5
Rocker cover ........................................................... 1.2.4
Engine................................................................1.7.1
Rod--connecting ...................................................... 1.6.1
Injector ................................................................14.2
Rod--push................................................................ 1.2.1
Injector (checking) ................................................2.0
Rotation--engine ............................................................. *
Torque specifications (see specific part)
Run in instructions ................................................. 13.2.1
Transistor regulator ..................................................7.1.1
S
Trouble shooting:
Electrical system...................................................7.0
Seals--crankshaft oil ................................................ 1.3.2
Engine.................................................................15.2
Serial designation ........................................................... *
Exhaust valve .......................................................1.0
Specifications:
Fuel injector ..........................................................2.0
Coolant............................................................... 13.3
Fuel pump.............................................................2.0
Fuel oil ............................................................... 13.3
General ...............................................................15.2
General .................................................................... *
Starting system ...................................................15.2
Lubricating oil ..................................................... 13.3
Tube--fuel injector ....................................................2.1.4
Overhaul (see specific part)
Tune up procedures (see contents page) ....................14
Spray tips--fuel injector............................................... 2.0
Starting aids--cold weather....................................... 12.6
Two cycle principle......................................................... *
Starting--cold weather .............................................. 12.6
Starting--engine ........................................................ 13.1
*General Information Section
Page 448