CHAPTER 1
INTRODUCTION
Section I. GENERAL
1-1. Scope
1-3. Reporting of Errors
This manual contains instructions for the use of direct
Report
of
errors,
omissions,
and
and general support personnel maintaining the Hughes-
recommendations
for
improving
this
Keenan Model VSH-10(Army Model MHE-194)
publication by the individual user is
warehouse crane truck as allocated by the Maintenance
encouraged. Reports should be submitted on
Allocation Chart.
DA Form 2028 (Recommended Changes to
1-2. Forms and Records
Publications) and forwarded direct to the
Maintenance forms, records, and reports which are to
Commanding General, U. S. Army Mobility
be used by maintenance personnel are listed in
Equipment Command, ATTN: AMSME-MPP,
TM 38-750.
4300 Goodfellow Boulevard, St. Louis, Mo.
63120.
Section II. DESCRIPTION AND DATA
Front servo-to-transmission case
1-4. Description
bolts....................................................... .30-35
A general description of the warehouse crane truck,
Rear servo-to-transmission case
Hughes-Keenan Model VSH-10 (Army Model
bolts . ..................................................... 40-45
MHE 194) is contained in TM 10-3950-203-10.
Planetary support-to-transmission
1-5. Identification, and Tabulated Data
case bolts............................................... 20-25
a. Identification Plate. Located on right side of
Oil distributor-to-oil distributor
cab below instrument panel, contains the boom lift
sleeve bolts .............................................. 8-10
capacity, serial number, Federal stock number, and
Upper valve body-to-lower valve
service weight.
body bolts................................................... 4-6
b. Tabulated Data. Refer to TM 10-3950-203-
Control valve body-to-transmission
20 for the tabulated data for the warehouse crane
case bolts ................................................ 8-10
truck.
Pressure regulator assembly-to-transmission
c. Torque Data.
case bolts . ............................................ 17-22
(1) Engine.
Extension assembly-to-transmission case
bolts . ..................................................... 10-13
Torque (ft-lbs
Detent lever attaching nut......................... 35-40
Cylinder head nuts...........................70-75
Converter cover drain plug ........................ 7-10
Main bearing caps. ..........................70-75
transmission vent assembly . ..................... 7-10
Connecting rods . .............................. .
35-40
Control valve body plug .......................... 10-14
Flywheel . ...........................................
70-75
Control valve lower body plug..................... 7-15
Intake manifold nuts . .........................
40-50
(3) Differential.
Exhaust manifold nuts . ......................
40-50
Water pump connecting nuts . ...........
50-55
,Cover-to-case bolt nuts............................ 47-52
Front-and rear-end plates . ................
50-55
Pinion cage capscrews-and stud nuts ...... 47-52
Gear covers . .....................................
50-55
Differential case bolt, nuts, and
Flywheel housing bolts ......................
50-55
capscrews .............................. ............. 82-91
Pinion shaft nuts .
175-200
(2) Transmission.
Gear-to-case capscrews .. ....................... 38-42
Case assembly gage hole plug..........
7-15
d. Engine limits and clearances.
Oil pan drain plug . .............................
20-25
( 1 ) Valve guide.
Rear band adjusting screw
Length . ........................................... 2-5 / 16 in.
locknut . ..........................................
35-40
Outside diameter . .....................6575 / .6565 in.
Front band adjusting screw
Stem hole diameter . ..................3432 /.3422 in.
locknut . ..........................................
20-25
Wear limits, maximum diameter .........1 447 in.
Converter cover-to-converter
Distance, cylinder block .......... ..... 1-15/32 in.
pump nuts . .....................................
15-28
(2) Valves, intake.
Converter pump hub-to-converter
Stem diameter............................ .3414/.3406 in
pump housing bolts . ......................
8-10
Front pump-to-transmission case
.
bolts .................................................
17-22
1-1
