equipments supported. Items authorized for use as
(3) Recoverability code indicates whether
required but not for initial stockage are identified with an
unserviceable items should be returned for recovery or
asterisk in the allowance column.
salvage.
Items not coded are expendable.
Recoverability codes are:
(2)
The
quantitative
allowances
for
Code
Explanation
organizational level of maintenance represents one
initial prescribed load for a 15-day period for the number
R Applied to repair parts (assemblies and
of equipments supported.
Units and organizations
components)
which
are
considered
authorized additional prescribed loads will multiply the
economically repairable at direct and general
number of prescribed loads authorized by the quantity of
support maintenance levels.
When the
repair parts reflected in the appropriate density column
maintenance capability to repair these items
applicable to the number of items supported to obtain
does not exist, they are normally disposed of at
the total quantity of repair parts authorized.
the GS level. When supply considerations
(3) Organizational units providing maintenance
dictate, some of these repair parts may be listed
for more than 100 of these equipments shall determine
for automatic return to supply for depot level
the total quantity of parts required by converting the
repair as set forth in AR 710-50. When so
equipment quantity to a decimal factor by placing a
listed, they will be replaced by supply on an
decimal point before the next to last digit of the number
exchange basis.
to indicate hundredths, and multiplying the decimal
T Applied to high dollar value recoverable repair parts
factor by the parts quantity authorized in the 51-100
which are subject to special handling and are
allowance column. Example, authorized allowance for
issued on an exchange basis. Such repair parts
51-100 equipments is 40; for 150 equipments multiply
normally are repaired or overhauled at depot
40 by 1.50 or 60 parts required.
maintenance activities.
(4) Subsequent changes to allowances will be
U Applied to repair parts specifically selected for
limited as follows: No change in the range of items is
salvage by reclamation units because of
authorized.
If additional items are considered
precious metal content, critical materials, high
necessary, recommendation should be forwarded to U.
dollar value reusable casings or castings.
S. Army Mobility Equipment Command for exception or
(4) This column also lists, below the SMR code,
revision to the allowance list. Revisions to the range of
an index number for each item in ascending numerical
items authorized will be made by this Command based
sequence, which is used to locate items in the
upon engineering experience, demand data, or TAERS
publication when the Federal stock number and/'or
information.
reference number is known.
h. Illustration, Column (8). This column is divided
b. Federal Stock Number. This column indicates
as follows:
the Federal stock number for the item.
(1) Figure number column (8)(a). Indicates the
c. Description. This column indicates the Federal
figure number of the illustration in which the item is
item name and any additional description of the item
shown.
required. A part number or other reference number is
(2) Item number, column (8)(b). Indicates the
followed by the applicable five-digit Federal supply code
callout number used to reference the item in the
for manufacturers in parenthesis. Material required for
illustration.
manufacture or fabrication is identified.
4. Special Information
d. Unit of Issue. This column indicates the unit
used as a basis for issue, e.g., ea, pr, ft, yd, etc.
a. Repair parts mortality has been based on 3, 000
e. Quantity Incorporated in Unit Pack. This column
hours of operation per year.
b. Parts which require manufacture or assembly at
indicates the actual quantity contained in the unit pack
a category higher than that authorized for installation will
(Not Applicable).
f. Quantity Incorporated in Unit. This column
indicate in the source column the higher category.
c. The following publications pertain to the
indicates the quantity of the item used in the functional
warehouse crane and its components:
group.
g. Fifteen-Day
Organizational Maintenance
TM 10-3950-204-10
Operator's manual.
Allowance, Column (4) of Section II and Column (7) of
TM 10-3950-204-20
Organizational mainte-
nance manual.
(1) The allowance columns are divided into four
subcolumns.
Indicated in each subcolumn is the
quantity of items authorized for the number of
iv