(1) Figure number, column (7) (a). Indicates
b. Federal Stock Number. This column indicates
the figure number of the illustration in which the item is
the Federal stock number for the item.
shown.
c. Description.
This column indicates the
(2) Item number, column (7) (b) Indicates the
Federal item name and any additional description of the
callout number used to reference the item in the
item required. A part number or other reference number
illustration.
is followed by the applicable five-digit Federal supply
code for manufacturers in parentheses.
Material
4. Special Information
required for manufacture or fabraction is identified.
a. Repair parts mortality has been based on
Repair parts quantities included in kits, sets and
3,000 hours operation per year for Crane (sec. IV, part
assemblies, not applicable to the end item, are shown in
I) and 1200 hours operation per year for Carrier (sec. IV,
parenthesis following the repair part name.
part II) and 3000 hours operation per year for
d. Unit of Issue. This column indicates the unit
winterization (sec. IV, part III).
used as a basis for issue, e.g., ea, pr, ft, yd, etc.
b. Parts which require manufacture or assembly
e. Quantity Incorporated in Unit. This column
at a category higher than that authorized for installation
will indicate in the source column the higher category.
indicates the quantity of the item used in the functional
c. The following publications pertain to the crane-
group.
shovel and its components:
f.
Fifteen-Day
Organizational
Maintenance
TM 5-3810-227-15
Operator, organizational,
Allowance, Column (3) of Section II and Column (6) of
DS, GS, and depot
Section III and IV.
maintenance
(1) The allowance columns are divided into
manual.
four subcolumns. Indicated in each subcolumn is the
LO 5-3810-227-15-1-2-3-4
Lubrication order
quantity of items authorized for the number of
5. How to Locate Repair Parts
equipments supported. Items authorized for use as
a. When Federal stock number or reference
required but not for initial stockage are identified with an
number is unknown:
asterisk in the allowance column.
(1) First.
Using the table of contents,
(2) The
quantitative
allowances
for
determine the functional group within which the repair
organizational level of maintenance represents one
part belongs.
initial prescribed load for a 15 - day period for the
(2) Second. Find the illustration covering the
number of equipments supported.
Units and
organizations authorized additional prescribed loads will
functional group to which the repair part belongs.
multiply the number of prescribed loads authorized by
(3) Third. Identify the repair part on the
the quantity of repair parts reflected in the appropriate
illustration, and note the illustration figure and item
density column applicable to the number of items
number of the repair part.
supported to obtain the total quantity of repair parts
(4) Fourth. Using the Repair Parts Listing,
authorized.
find the functional group to which the repair part belongs
(3) Organizational
units
providing
and locate the illustration figure and item number noted
maintenance for more than 100 of these equipments
on the illustration.
shall determine the total quantity of parts required by
b. When Federal stock number or reference
converting the equipment quantity to a decimal factor by
number is known:
placing a decimal point before the next to last digit of
(1) First. Using the Index of Federal Stock
the number to indicate hundredths, and multiplying- the
Numbers and Reference Numbers, find the pertinent
decimal factor by the parts quantity authorized in the 51-
Fed-Stock Number or Reference Number. This index is
100 allowance column. Example, authorized allowance
in ascending alpha-numeric sequence cross-referenced
for 51-100 equipments is 40; for 150 equipments
to an index number.
multiply 40 by 1.50 or 60 parts required.
(2) Second. Using the Repair Part Listing,
(4) Subsequent changes to allowances will
find the index number referenced in the Index of Federal
be limited as follows: No change in the range of items is
Stock Numbers and Reference Numbers.
authorized.
If additional items are considered
6. Abbreviations
necessary, recommendation should be forwarded to
cl .................................. coil
U.S. Army Mobility Equipment Command for exception
cu ................................. cubic
or revision to the allowance list. Revisions to the range
deg ............................... degree(s)
of items authorized will be made by this Command
dia ................................ diameter
based upon engineering experience, demand data, or
ea ................................. each
TAERS information.
ft................................... feet (foot)
h. Illustration, Column (7).
This column is
gal ................................ gallon (s)
divided as follows:
grp ................................ group
id .................................. inside diameter
vi
