1
Screw, cap, M(-28 x 1 in. (6 rqr)
6
Retaining plate, external
2
Washer, lock, 13 in. (6 rqr)
7
Retaining plate, internal
8
Screw, 10-82 x 1l% in. (6 rqr)
8
Bearing, sealed
4
Washer, lock, IT, No. 10 (6 rqr)
9
Drive end frame
5
Collar
10
Armature
A. Armature and drive end frame
1
Cover band assembly
11
Nut, No. 10-82 (4 rqr)
2
Screw, 10-82 x 3/8 in. (5 rqr)
12
Washer, lock, No. 10 (4 rqr)
8
Washer, lock, No. 10 (5 rqr)
18
Commutator end plate.
4
Brush (4 rqr)
14
Bearing, sealed
5
Lead assembly
15
Screw, special (4 rqr)
6
Screw, 10-82 x 3/8 in. (4 rqr)
16
Dowel pin, 3/16 x 1/2 in.
7
Washer, lock, No. 10 (4 rqr)
17
Brush arm (4 rqr)
8
Screw, cap, 1-28 x 1 in. (6 rqr)
18
Spacer washer
9
Washer, lock, in. (6 rqr)
19
Spring (4 rqr)
10
End cover plate
20
Brush plate assembly
B. Commutator end fram and brushes
1
Screw, 10-82 x 1A6 in. (4 rqr)
5
Screw, 10-32 x 13/16 in. (4 rqr)
2
Washer, lock, No. 10 (4 rqr)
6
Washer, lock, No. 10 (4 rqr)
3
Elbow
7
Terminal receptacle
4
Gasket
8
Spacer block
C. Outlet receptacle
1
Screw, 10-32 x 3/8 in. (5 rqr)
5
Field coil (4 rqr)
2
Washer, lock, No. 10 (5 rqr)
6
Insulation band
3
Pole shoe screw (8 rqr)
7
Dowel pin, 3/16 x 3/4 in.
4
Pole shoe (4 rqr)
8
Field coil frame
D. Field coils, field coil frame, and pole shoes
Figure 7. -Continued.
b. Inspection and Repair. Inspect all parts for
brushes and has an intermediate bearing to support the
excessive wear or damage. Replace or repair all
armature shaft in the middle, while the ends are
defective parts. Refer to TM 5-764 for armature and
supported by bushings.
field coil tests.
68. Crane Engine Starter Assembly Removal and
70. Crane Engine Starter Assembly Reassembly and
Disassembly
Installation
a. Removal. Remove the starter (TM 5-3810-207-
a. Reassembly. Reassemble the starter in the
20).
reverse of the numerical sequence as illustrated on
b. Disassembly.
Disassemble the starter in
b. Installation. Install the starter (TM 5-3810-207-
numerical sequence as illustrated on figure 9.
20).
69.
Crane Engine Starter Assembly Cleaning,
Inspection, and Repair
a. Cleaning. Clean all parts with an approved
cleaning solvent and dry thorough
Section VII. CRANE ENGINE DISTRIBUTOR ASSEMBLY
terminal inlet is set at an angle to the distributor
71. General
housing, to prevent mounting space.
The crane engine distributor assembly is a 24-volt
72. Crane Engine Distributor Assembly Removal
grounded type distributor.
The distributor is radio
suppressed through a built-in system consisting of a
and Disassembly
primary connection capacitor, an ignition coil capacitor,
a. Removal. Remove the distributor (TM5-3810-
and resistors at each high tension outlet of the
207-20).
distributor cap, as well as one built into the rotor. The
b. Disassembly.
Disassemble the distributor
primary
numerical sequence as illustrated on figure10
TAGO 5030A
39