1
Cap
18
Washer, lock, IET, No. 10 (4 rqr)
2
Screw, machine, 8-32 x in. (2 rqr)
19
Burner assembly
3
Washer, lock, IET, No. 8 (2 rqr)
20
Burner gasket
4
Switch plate
21
Hose clamp
5
Screw, machine, 10-32 x 5/16 in. (8 rqr)
22
Duct tube
6
Washer, lock, IET, No. 10 (8 rqr)
23
Wick retaining nut
7
Rear heater ring
24
Wick retainer washer
8
Nut, hex I'rl,-18 (5 rqr)
25
Burner wick assembly
9
Washer, lock, IET, 5/16 in. (5 rqr)
26
Generator assembly
10
Screw, cap, hex hd, 5/16-18 x 1 in. (5 rqr)
27
Mixing ring
11
Heater base assembly
28
Burner head
12
Blower casing assembly
29
Igniter sleeve gasket
13
Heater clamp
30
Igniter sleeve
14
Front mounting ring
31
Elbow assembly
15
Combustion casing assembly
32
Igniter
16
Combustion chamber assembly
33
Igniter gasket
17
Screw, machine, 10-32 x 9/16 in. (4 rqr)
Figure 49. -Continued.
b. Disassembly.
Disassemble the carrier engine
burner wick.
(4) Inspect the wires for deteriorated or cut
heater (par. 191).
covering and loose connections. Repair or
replace defective wire as necessary.
196. Carrier Engine Heater Cleaning,
(5) Always use new grommets, gaskets, and
Inspection, and Repair
washers, during reassembly.
a. Cleaning. Clean all parts with an approved
cleaning solvent.
197. Carrier Engine Heater Reassembly and
b. Inspection and Repair.
Installation
(1) Inspect the rings, clamps, casing
a. Reassembly. Reassemble the carrier engine
assembly, funnel, chamber assembly,
heater (par. 193).
generator, fan, support assembly, scroll,
b. Installation.
and the scroll body, for dents, cracks,
(1) Install the carrier engine heater blower
bends, or other damage. Replace parts
(TM 5-3810-207-20).
as necessary.
(2) Install the carrier engine heater controls
(2) Inspect the screws, nuts, igniter, sleeve,
and control box (TM 5-3810-207-20).
elbow, and cap for stripped threads or
(3) Install the carrier engine heater (TM 5-
other damage. Replace defective parts as
3810-207-20).
necessary.
(3) Use a wire to clean out the holes in the
Section III. CARRIER CAB HEATER
(2) Remove the carrier cab heater control box
198. General
(TM 5-3810-207-20).
The carrier cab heater is mounted on the outside rear
b. Disassembly.
Disassemble the carrier cab
of the cab, near the bottom of the rear panel. The
heater in numerical sequence as illustrated on figure 50.
purpose of the heater is to deliver fresh, heated air to the
cab and defrosters.
200. Carrier Cab Heater Cleaning,
199. Carrier Cab Heater Removal and
Inspection, and Repair
a. Cleaning. Clean all parts with an approved
Disassembly
cleaning solvent and dry thoroughly.
a. Removal.
(1) Remove the carrier cab heater (TM 5-
3810-207-20).
TAGO 5030A
97
