1
Screw, machine, 5/16-18 x 1/2 in. (4 rqr)
22
Shifting yoke block, 1st and reverse
2
Washer, lock, 5/16 in. (4 rqr)
28
Shifting yoke, 1st and reverse
8
Top plate
24
Shifting yoke, 2nd and 3rd
4
Gasket
25
Shifting yoke, direct and overdrive
5
Lockwire
6
Screw, cap, 3/8-16 x 1 in.
B.
Shifting bars, yokes and housing
7
Inner shift lever
8
Plug, pipe, 3/8 in.
1
Screw, cap, special, 3/8-16 x 1 1/2 in. (2 rqr)
9
Spring
2
Screw, cap, 3/8-16 x 1 1/4 in. (4 rqr)
10
Ball, steel, 1/2 in.
3
Washer, lock, 3/8 in. (6 rqr)
11
Shifting shaft
4
Front bearing cover
12
Top cover housing
5
Cover gasket
A. Carrier engine transmission top cover
C. Front bearing cover
1 Screw, cap, 3/8-16 x 1 1/4 in. (2 rqr)
1
Pin cotter, 1/8 x 2 1/2 in.
2 Washer, lock, 3/8 in. (2 rqr)
2
Nut, special, 1 1/4l-18
8 Cover
3
Washer, flat, 1 1/4 in.
4 Cover gasket
4
Yoke
5 Position finder spring (8 rqr)
5
Plug
6 Ball, steel, 1/2 in. (3 rqr)
6
Screw, cap, 3/8-16 x 5/8 in. (8 rqr)
7 Expansion plug
7
Washer, lock, 3/8 in. (8 rqr)
8 Screw, cap, 3/8-16 x 2 1/4 in. (2 rqr)
8
Rear bearing cover
9 Washer, lock, 3/8 in. (2 rqr)
10 Screw, cap, 3/8-16 x 1ik in. (14 rqr)
9
Cover gasket
11 Washer, lock, 3/8 in. (14 rqr)
D. Rear bearing cover
12 Shifter bar housing
13 Housing gasket (3 rqr)
14 Lockwire (3 rqr)
1
Plug, pipe, 1 1/4 in.
15 Lockscrew (4 rqr)
2
Screw, cap, 3/8-16 x 5/8 in. (12 rqr)
16 Expansion plug (8 rqr)
3
Washer, lock, 3/8 in. (12 rqr)
17 Interlock pin
4
Cover (2 rqr)
18 Direct and overdrive shifting bar
5
Gasket (2 rqr)
19 Shifting bar, 2nd and 3rd
6
Transmission case
20 Shifting bar, 1st and reverse
21 Ball, steel, 3/4 in. (2 rqr)
E.
Transmission case
Figure 85-Continued.
then transmitted to the transfer case by means of a
308.
Carrier Transmission Assembly Cleaning,
Inspection, and Repair
a special alloy steel and then heat-treated. The gears,
a. Cleaning. Clean all parts with an approved
shaft, and bearings operate constantly in an oil bath.
cleaning solvent and dry thoroughly.
The entire transmission is inclosed.
b. Inspection and Repair. Inspect all parts for
307.
Carrier Transmission Assembly Removal and
excessive wear and damage. Replace or repair all
Disassembly
damaged or defective parts.
a. Removal.
309.
Carrier Transmission Assembly Reassembly
(1) Drain the transmission assembly (TM 5-
and Installation
3810-207-10).
a. Reassembly.
Reassemble
the
carrier
(2) Disconnect the propeller shaft (TM 5-
transmission assembly in the reverse of the numerical
3810207-20).
sequence as illustrated on figure 85.
(3) Remove the carrier transmission assembly
b. Installation.
as instructed on figure 84.
(1) Install the carrier engine clutch housing as
(4) Remove the carrier engine clutch' housing
instructed on figure 68.
as instructed on figure 68.
(2) Install the carrier transmission assembly
b. Disassembly.
Disassemble the carrier
as illustrated on figure 84.
transmission assembly in numerical sequence as
(3) Connect the propeller shaft (TM 53810-
illustrated on figure 85.
207-20).
(4) Fill the transmission case assembly (TM
5-3810-207-10).
TAGO 5030A
143
