1
Screw, cap, -10 x 1 in. (8 rqr)
3
Washer, lock, 3/8 in. (6 rqr)
2
Washer, lock, in. (3 rqr)
4
Backplate assembly, w/pawl
3
Bolt, socket-head, 10 x 1 in.
5
Nut, 7/16-14 (6 rqr)
4
Washer, lock, in.
6
Washer, lock, 7/16 in. (6 rqr)
5
Transfer case front mounting
7
Rear bearing cage assembly
A. Transfer case front mounting
8
Shim (as rqr)
9
Shim (as rqr)
1
Pin, cotter, 1/16 x 1 in.
10
Shim (as rqr)
2
Nut, special, -12
11
Bearing-to-flange spacer
3
Brakedrum
12
Stud, 7/16-14 x 1 in. (6 rqr)
4
Nut, 3/8-16 (8 rqr)
13
Bearing cage dowel pin
5
Washer, lock, 3/8 in. (8 rqr)
14
Oil seal
6
Screw, cap, 3/8-16 x 1 in. (8 rqr)
15
Bearing cup
7
Flange yoke
C. Backplate assembly
8
Mounting flange
9
Spring (2 rqr)
1
Transfer case rear mounting
10
Brake shoe assembly (2 rqr)
2
Screw, cap, 7/16-14 x 1 1/6 in. (6 rqr)
11
Cam operating lever
3
Washer, lock, 7/16 in. (6 rqr)
12
Rivet (28 rqr)
4
Rear bearing cover
13
Brake lining (2 rqr)
5
Shim (as rqr)
6
Shim (as rqr)
B. Brake shoe assembly
7
Shim (as rqr)
1 Roller
8
Rear bearing cup
2 Screw, cap, 3/8-16 x 16 x 1 in. (6 rqr)
D. Rear mounting and bearing cover
Figure 95.-Continued.
Section III. CARRIER REAR SERVICE BRAKE ASSEMBLY
344. Carrier Rear Service Brake Assembly Cleaning,
342. General
The carrier rear service brake assembly is a two
Inspection, and Repair
shoe, automotive-type, air-actuated brake. The friction
a. Cleaning. Clean all parts with an approved
set up between the relative motion of the brakeshoe
cleaning solvent and dry thoroughly.
linings and the brakedrum retards the motion of the
b. Inspection and Repair. Inspect all parts for
wheels on the carrier axle.
excessive wear and damage. Replace and repair all
defective parts.
343. Carrier Rear Service Brake Assembly Removal
and Disassembly
345. Carrier Rear Service Brake Assembly
a. Removal. Remove the carrier rear service
Reassembly and Installation
brakeshoe (TM 5-3810-207-20).
a. Reassembly.
Reassemble the carrier rear
b. Disassembly.
Disassemble the carrier rear
service brake assembly in the reverse of the numerical
service brake assembly in numerical sequence as
sequence as illustrated on figure 97.
illustrated on figure 97.
b. Installation.
Install the carrier rear service
brakeshoe (TM 54810-207-20).
Section IV. CARRIER AIR ASSIST VALVE ASSEMBLY
346. General
348. Carrier Air Assist Valve Assembly Cleaning,
The carrier air assist valve assembly is air-actuated
Inspection, and Repair.
and is used to reduce the effort required to apply the
a. Cleaning. Clean all parts with an approved
handbrake.
cleaning solvent and dry thoroughly.
b. Inspection and Repair. Inspect all parts for
347. Carrier Air Assist Valve Assembly Removal
excessive wear and damage. Replace or repair all
and Disassembly
defective parts.
a. Removal. Remove the carrier air assist valve
assembly (TM 5-3810-207-20).
349. Carrier Air Assist Valve Assembly Reassembly
b. Disassembly. Disassemble the carrier air assist
and Installation
valve assembly in numerical sequence as illustrated on
a. Reassembly. Reassemble the carrier air
TAGO 5030A
163
