TM 5-3810-289-24P F - Direct  support  or  aviation  intermediate  is  the lowest level than can do complete repair of the item. H - General support is the lowest level that can do complete repair of the item. L - Specialized repair activity is the lowest level that can do complete repair of the item. D - Depot is the lowest level that can do complete repair of the item. Z - Nonreparable.  No repair is authorized. B - No  repair  is  authorized.    (No  parts  or  special tools  are  authorized  for  the  maintenance  of  a “B”  coded  item.)     However,  the  item  may  be reconditioned  by  adjusting,  lubricating,  etc.,  at the user level. (3) Recoverability    Code.        Recoverability codes are assigned to items to indicate the disposition action  unserviceable  items.    The  recoverability  code  is entered in the fifth position of the SMR code as follows: Code Application/Explanation Z - Nonreparable    item.        When    unserviceable, condemn and dispose of the item at the level of maintenance  shown  in  the  3d  position  of  the SMR code. O - Reparable item. When uneconomically reparable, condemn and dispose of the item at unit maintenance or aviation unit level. F - Reparable item. When uneconomically reparable, condemn and dispose of the item at the direct support or aviation intermediate level. H - Reparable item. When uneconomically reparable, condemn and dispose of the item at the general support level. D - Reparable   item.      When   beyond   lower   level repair capability, return to depot. Condemnation     and     disposal     of     item     not authorized below depot level. L - Reparable item.  Condemnation and disposal of item   not   authorized   below   specialized   repair activity (SRA). A - Item requires special handling or condemnation procedures  because  of  specific  reasons  (e.g., precious    metal    content,    high    dollar    value, critical material, or hazardous material).  Refer to   appropriate   manuals/directives   for   specific instructions. c. FSCM  or  CAGEC  (Column  (3)).    The  Federal Supply     Code     for     Manufacturer     (FSCM)     or     The Commercial  and  Government  Entity  (CAGE)  Code  (C) is a 5-digit alphanumeric code which is used to identify the  manufacturer,  distributor,  or  Government  agency, etc., that supplies the item. d. PART  NUMBER  (Column  (4)).    Indicates  the primary  number  used  by  the  manufacturer  (individual, company,   firm,   corporation,   or   Government   activity), which controls the design and characteristics of the item by  means  of  its  engineering  drawings,   specifications standards,  and  inspection  requirements  to  identify  an item or range of items. NOTE:   When   you   use   an   NSN   to   requisition   an item, the item you receive may have a different part number from the part ordered. e. DESCRIPTION    AND    USABLE    ON    CODE (UOC) (Column (5)).  This column includes the following information: (1) The   Federal   item   name   and,   when required, a minimum description to identify the item. (2) Physical   security   classification.      Not Applicable. (3) Items that are included in kits and sets are listed below the name of the kit or set on Figure KIT. (4) Spare/repair   parts   that   make   up   an assembled   item   are   listed   immediately   following   the assembled item line entry. (5) Part   numbers   for   bulk   materials   are referenced  in  this  column  in  the  line  item  entry  for  the item to be manufactured/fabricated. (6) When the item is not used with all serial numbers    of    the    same    model,    the    effective    serial numbers are shown on the last line(s) of the description (before UOC).  Not Applicable. (7) The  usable  on  code,  when  applicable (see paragraph 5, Special Information). (8) In  the  Special  Tools  List  section,  the basis  of  issue  (BOI)  appears  as  the  last  line(s)  in  the entry  for  each  special  tool,  special  TMDE,  and  other special support equipment. When density of equipments supported exceeds density spread indicated in the basis of issue, the total authorization is increased proportionately. (9) The    statement    “END    OF    FIGURE” appears just below the last item description in Column 5 for a given figure in both Section II and Section III. f. QTY   (Column   (6)).      The   QTY   (quantity   per figure column) indicates the quantity of the item used in the  breakout  shown  on  the  illustration/figure,  which  is prepared for a functional group, subfunctional group, or an assembly.  A “V” appearing in this column in lieu of a quantity  indicates  that  the  quantity  is  variable  and  the quantity may vary from application to application. Change 1  3