TM 5-3810-294-34
retaining rings (20). Install bearing caps and secure
361 and bearing retainer (411 on housing. Secure
with screws (21). Tighten the screws to a torque of
retainer with nuts (491 and washers (50). Tighten
290 to 370 foot-pounds. Install lock wire (17).
nuts to a torque of 53 to 67 foot-pounds.
q. Check end play of gear (4). End play in
I. Check gear backlash in bevel gear set (16).
differential bearings should be 0.0005 inch. -
Backlash should be 0.020 to 0.026 inch. Check
16-13. Installation
tooth contact between bevel gears. Adjust backlash
a. Install new gasket on differential housing
by removing or installing shims under retainers (27
flange. Install differential carrier assembly on axle
and (621.
housing studs, and secure with nuts (112, fig. 16-
m. Install one washer (15) and one gear (6) in
5).
one case half (3). Install spider (9) with gears (8)
b. Push the axle assembly toward the dif-
anti washers (7), in position in case half.
ferential and rotate the brake drum until the splines
n. Position gear (4) on case half and install other
in axle shaft (66) engage side gears (6). Install
case half (3). Align mating marks and draw parts
screws (70), washers (103), and nuts (104).
together with four bolts (1) and nuts (10). Check
Tighten the nuts to 250 to 300 foot-pounds.
assembly for free rotation. Install remaining bolts
c. Install the tie rod assembly and secure with
and nuts and tighten to a torque of 53 to 67 foot-
bolts (75) and nuts (87). Install cotter pin (86).
pounds. Secure nuts with cotter pins (11).
d. Refer to paragraph 11-11 and install the axle
o. Install bearings (2) on bearing surfaces of
assembly on the crane carrier.
case halves.
p. Install differential assembly on carrier
housing with bearings in bearing cap bores. Install
Section III. REPAIR OF FRONT AXLE ASSEMBLY
16-14. Removal
a. Refer to paragraph 11-11 and remove the
front axle from the crane carrier.
b. Refer to paragraph16-8 and remove the
KEY to fig. 16-511)
differential assembly from the front axle.
1. Screw (4)
36.
Washer(24)
16-1 5. Disassembly
2. Washer (4)
37.
Spindle (2)
3. Plate (2)
38.
Bushing 2)
Refer to figure 16-5 and disassemble the front axle
4. Packing (2}
39.
Bushing
as follows:
5. Washer (2)
40.
Bolt {24)
6. Retaining ring (2)
41.
Washer(241
7. Driving flange (2)
42.
Nut (24)
8. Nut (161
43.
Screw (4
9. Washer (16)
44.
Stud (24)
10. Gasket (2)
45.
Retainer (2)
11. Packing(2)
46.
Bearing(4)
12. Nut (2)
47.
Bearing cup (4)
13. Key washer (2)
48.
Shim
14. Washer (2)
49.
Shim
15. Nut 121
50.
Washer (2)
16. Bearing (21
51.
Nut (2)
17. Bearing cup 121
52.
Nut (2)
18. Stud (16)
53.
Washer(2)
19. Nut (20)
54.
Ball stud
20. Stud (20)
55.
Steering arm
21. Wheel hub (2)
56.
Nut
22. Brake drum (2)
57.
Cotter pin
23. Nut (20)
58.
Stud (21
24. Bolt (2)
59.
Flange (2)
25. Retainer (2)
60.
Washer (4)
26. Spring (2)
61.
Ball joint (21
27. Brake shoe (2)
62.
Inner race (2)
28. Brake shoe (2)
63.
Ball cage (2)
29. Camshaft (2)
64.
Retaining ring (2)
30. Bushing (41
65.
Ball (24)
31. Bearing cup (2)
66.
Axle shaft ( 2)}
32. Anchor pin (4)
67.
Bearing cap (3)
33. Bearing (21
68.
Washer (12)
34. Oil seal 12)
69.
Screw(12)
35. Nut (24)
16-10
