TM 5-3810-295-34
(4) Dimensions and transportation data
Overall lengths with boom in travel position537 in
(a) Nut and bolt torque data (carrier engine).
Overall length without boom
.................. 351 in
Main bearing capscrews
Overall width w/mirror
.................. 1491 in
torque requirements
Overall width w/o mirror
..................
141 in
1. Tighten to ................................... 150-160 foot-pounds
Overall height with cab
.................. 1491/2 in
(ft-lb)
Overall height w/o upper cab housing ........... 132 in
(203-217 Nim)
Overall height with boom in travel position .... 167 in
Shipping cubage
... 3.810 ft 3
2. Advance to ......................... 340-350 ft-lb (461-475
Nim)
Shipping tonnage
(5) Approximate weights.
3. Loosen All
Truck crane with boom
.................. 66,740 lb
4. Tighten to ................................... 85-90 ft-lb (115-122
Nim)
Truck crane w/o boom
.................. 62,724 lb
Carrier complete
... 41,763 lb
5. Tighten to .............................. 170-180 ft-lb (230-244
Crane upper w/Half Tank of Fuel ..................
Nim)
20,400 lb
6. Advance to ................................. 60 degrees or 1 hex in
Boom tip section with two guy lines
30
attached
.................. 1,511 lb
............
increments
Guy lines, 15 foot, set of two
.................. 140 lb
Main bearing side bolts
Boom base section
.................. 1,022 lb
torque requirements
Upper spreader
........ 200 lb
1. Tighten to ................................... 25-35 ft-lb (34-47
Hook block
........ 475 lb
Nim)
Boom backstops with pins
.................. 824 lb
2. Tighten to ................................... 70-75 ft-lb (95-102
(6) Speed (full throttle and full load).
Nim)
Rear drum shaft
.... 43.6 rpm
3. Advance to ........................... 140-150 ft-lb (190-203
Front drum shaft raising
..................
43.6
Nim)
rpm
Connecting rod nuts
Front drum shaft lowering
.................. 23.56 rpm
torque requirements
Front drum line speed lowering .................. 82.45 fpm
1. Tighten to ................................... 50-60 ft-lb (67-81
Boom hoist drum shaft
.................. 87.20 rpm
Nim)
Boom hoist drum shaft lowering .................. 41.31 rpm
2. Advance to .............................. 90-100 ft-lb (122-136
Boom hoist drum line speed, lowering .......... 102.68 fpm
Nim)
Revolving frame rotation
..................
3.94
3. Loosen All
rpm
4. Tighten to ................................... 30-40 ft-lb (41-54
(7) Rated capacities.
Nim)
Crane
5. Advance to .............................. 95-105 ft-lb (129-142
Boom hoist drum line pull
.................. 7,000 lb Nom.
Nim)
Rear drum line pull, sea level at 500 ft 18,260 lb
6. Advance .....................................
0.005-0.020 in
Rear drum line pull, 5,000 ft. Altitude ............ 17,410 lb
Vibration damper and
Front drum line pull, sea level at 500 ft17,650 lb
front pulley ........................... 200-205 ft-lb (271-278
Front drum line pull, 5,000 altitude ................ .16,830 lb
Nim)
(8) Fuel water, oil and grease capacities carrier.
Pipe plug torque
Engine fuel tank
...... 130 gal
1/8 inch ...................................... 5-15 ft-lb (7-20 Nim)
Cooling system
.......... 7 gal
3/8 inch ...................................... 30-45 ft-lb (41-61
Engine crankcase with filter
..................
28 qt
Nim)
Transmission and torque converter ...............
50 qt
inch ........................................ 45-55 ft-lb (61-75
Hydraulic system
........ 230 qt
Nim)
Front axle differential
..................
18 qt
Cylinder head capscrews ........................ 280-300 ft-lb (380-
Rear axle differential
..................
18 qt
401 Nim)
Wheel planetaries (4)
..................
12 qt
Injector hold-down capscrews .................... 30-35 ft-lb (41-
Steering gear boxes (3)
..................
12 qt
47 Nim)
(9) Fuel water, and oil capacities, crane.
Engine fuel tank
........ 56 gal
Valve crosshead adjusting
Cooling system
.......... 26 qt
screw nut ................................... 25-30 ft-lb (34-41
Nim)
Engine crankcase with filters
..................
12 qt
Air cleaner
...... 3 3/4 qt
Tappet plate capscrews ................... 18-22 ft-lb (24-30
Nim)
(10)Torque data
Intake manifold
NOTE
capscrews .................................. 30-32 ft-lb (41-43
Nim stands for Newton meters, a metric ex-
Nim)
pression of torque.
Exhaust manifold capscrews........................45-50 ft-lb (61-
