TM 5-3810-307-24-1-1
LEGEND for Figure 2-1-8
1. Refrigerant hose
41. Washer
81. Capscrew
121. Check valve
2. Refrigerant hose
42. Capscrew
82. Lockwasher
122. Gasket
3. Clamp
43. Motor
83. Bracket
123. Thrust plate
4. Clamp
44. Elbow
84. Bracket
124. Pocket seal
5. Nut
45. Tee
85. Cotter pin
125. Thrust plate
6. Lockwasher
46. Adapter
86. Retainer
126. Pocket seal
7. Washer
47. Tee
87. Fan
127. Bearing
8. Condenser
48. Nut
88. Nut
128. Seal ring
9. Capscrew
49. Lockwasher
89. Star washer
129. Snap ring
10. Lockwasher
50. Washer
90. Nut
130. Bearing
11. Cover
51. Capscrew
91. Star washer
131. Retainer
12. Screw
52. Flow divider valve
92. Capscrew
132. Seal
13. Cover
53. Adapter
93. Clamp half
133. Capscrew
14. Capscrew
54. Adapter
94. Fan motor
134. Cover
15. Drive belt
55. Tube
95. Nut
135. Capscrew
16. Refrigerant hose
56. Relief valve
96. Star washer
136. Retainer bar
17. Nut
57. Nut
97. Capscrew
137. Mount bracket
18. Lockwasher
58. Lockwasher
98. Clamp half
138. Screw
19. Washer
59. Washer
99. Drier
139. Retainer plate
20. Capscrew
60. Capscrew
100. Switch
140. Clip
21. Compressor
61. Washer
101. Grommet
141. Fan wheel
22. Nut
62. Bracket
102. Electrical harness
142. Capscrew
23. Lockwasher
63. Nut
103. Case
143. Resistor
24. Washer
64. Lockwasher
104. Capscrew
144. Nut
25. Lockwasher
65. Washer
105. Drive plate
145. Star washer
26. Washer
66. Capscrew
106. Shim
146. Capscrew
27. Bushing
67. Washer
107. Snap ring
147. Clamp half
28. Bracket
68. Evaporator assy.
108. Cover
148. Fan motor
29. Hydraulic hose
69. Refrigerant hose
109. Pulley
149. Capscrew
30. Hydraulic hose
70. Capscrew
110. Screw
150. Thermostat
31. Hydraulic hose
71. Lockwasher
111. Coil
151. Capscrew
32. Hydraulic tube
72. Capscrew
112. Capscrew
152. Side cover
33. Hydraulic tube
73. Lockwasher
113. Washer
153. Coil
34. Capscrew
74. Coil
114. Cover
154. Nut
35. Lockwasher
75. Relay
115. Gear housing
155. Star washer
36. Retainer
76. Screw
116. Bearing
156. Capscrew
37. Key
77. Socket
117. Seal ring
157. Connection block
38. Sheave
78. Capscrew
118. Cover
158. Grommet
39. Nut
79. Lockwasher
119. Gear
159. Electrical harness
40. Lockwasher
80. Mount bracket
120. Shaft
160. Case
b.
Assemble condenser assembly (8, Figure 2-1-8) as necessary:
(1)
If removed, route electrical harness (102) through hole in case (103), and install grommet (101) over
electrical harness (102) and into hole of case (103).
(2)
If removed, install switch (100) in drier (99).
(3)
Install drier (99) on bracket in case (103) with clamp halves (98), capscrews (97), star washers (96),
and nuts (95).
(4)
Connect electrical leads to switch (100) and remove tags.
2-1-55
