1
Filter plug
18
Lock
2
Washer
19
Drive
3
Filter screen
20
Spacer
4
Union body
21
Throttle shaft
5
Fiber washer
22
Snap ring
6
Screw, cap, -20 x in. (4 rqr)
23
Bearing
7
Washer, lock, 1A in. (4 rqr)
8
Bowl cover
9
Float axle
C. Carburetor lever and shaft
10
Float
11
Needle valve
1
Accelerator jet
12
Gasket
2
Accelerator jet
13
Pump
3
Metering well
14
Idle jet (2 rqr)
4
Secondary metering well
15
Valve seat
5
Metering well
16
Seat gasket
6
Well vent jet
17
Check valve body
7
Idle compensator jet (2 rqr)
18
Check valve ball
8
Jet washer (2 rqr)
9
Pump check valve
A. Carburetor cover, float, pump and idle jets
10
Check valve disk
11
Power jet and valve
1
Screw, 10-24 x 1 in. (4 rqr)
13
Discharge jet
2
Washer, lock, No. 10 (4 rqr)
13
Discharge jet
3
Throttle body
14
Jet washer
4
Gasket
15
Discharge jet
5
Screw, 8-32 x 9/16 in.
16
Jet washer
6
Washer, lock. No. 8
17
Plug, pipe, 41/8 in. (3 rqr)
7
Venturi
18
Main passage plug
8
Screw, 8-32 x 9/16 in.
19
Plug washer
9
Washer, lock, No.8
20
Main jet
10
Venturi
21
Jet washer
11
Idle adjusting needle
22
Screw, 1032 x 11X in.
12
Spring
23
Nut, 10-32
13
Plug, ping
23
Nut, 10-32
13
Plug, pipe, 1/8 in.
24
Main passage plug
14
Screw, 10-24 x in. (2 rqr)
25
Plug washer
15
Throttle plate
26
Main jet
16
Screw, 10-24 x in. (2 rqr)
27
Jet
17
Throttle plate x in. (2 rqr)
27
Jet washer
28
Screw, 10-32 x 11/8 in. (2 rqr)
29
Washer, lock, No. 10 (2 rqr)
B. Carburetor venturi, idle needle, and throttle body
30
Choke shaft cover plate
31
Cover plate gasket
32
Screw, 10-32 x %7/ in.
1
Screw, 10-32 x 9/16 in.
33
Nut, 10-32
2
Throttle lever
34
Screw, 10-32 x 1 in.
3
Screw, 10-32 x 13/8 in.
35
Washer, flat, No. 10
4
Spring
36
Choke spring
5
Pin
37
Choke lever
6
Throttle stop
38
Screw, 10-32 x 14% in. (2 rqr)
7
Bevel washer
39
Washer, lock, No. 10 (2 rqr)
8
Washer, special
40
Screw, 1032 x r1 in.
9
Packing
41
Cover plate
10
Sleeve bearing
42
Screw, 8-32 x 7/8 in. (3 rqr)
11
Idle stop screw (2 rqr)
43
Choke plate
12
Washer, lock, No. 6 (2 rqr)
44
Choke shaft
13
Support
45
Washer, lock, 3/8 in.
14
Spacer
46
Choke shaft washer
15
Gasket
47
Fuel bowl
16
Shaft
17
Screw, 10-32 x in.
D.
Carburetor metering wells, main jets, choke shaft, and fuel
bowl
Figure 51--Continued.
Section V. CARRIER ENGINE ASSEMBLY
suppression circuit built into the distributor. The radio
218. General
interference suppression system includes another
A waterproof-type distributor is used on the carrier
capacitor connected between the ignition coil positive
engine. This model is automatic, 24 volts, ground-type
terminal and ground, as well as built-in resistors at each
with a flange mounting. A waterproof primary connection
high tension outlet of the molded cap and also one built
on the distributor housing encloses a feed through
into the
capacitor which is part of the radio interference
TAGO 5030A
103
