TM 5-3810-294-34
(4) When clevis pins (21 and cotter pins (1)
KEY to fig. 14-2.
10.
Shift finger
(used with fingers 10 and 11) are removed, the
1. Critter pin (61
11.
Shift finger
universal lever (14), outside shift finger (111, and boot
2. Clevis pin (61
12.
Lock wire
(13) are accessible. Cut lockwire (12).
3. Bracket
13.
Boot
(5) Remove retaining ring (5) only if it is
4. Lock screw (21
14.
Lever
necessary to replace pivot anchor bracket (3).
5. Retaining ring
15.
Welch plug
b. Remove fourteen screws and lockwashers that
6. Shaft
16.
Yoke
secure the manual control assembly (fig. 14-4) to the
7. Control top
17.
Swivel bracket
transmission housing and remove manual control
8. Welch plug
18.
Retaining ring
assembly.
9. Woodruff key (2)
c. Shifting by hand, engage transmission into two
speeds at the same time.
(1) Remove remote control assembly from
d. Remove companion flange nut (29, fig. 14-5).
manual control assembly.
e. Remove drop gear unit (fig. 14-5) by removing
(2) Remove retaining ring (18, fig. 14-2 Remove
nuts (63) and lockwashers (62).
yoke (16) and swivel bracket (17) as assembly. Remove
f. Refer to figure 14-3 and remove cotter pin
two cotter pins (1) and two clevis pins (21).
(31), nut (32), and washer (33). Remove drop gear
(3) Remove locking screws (4) and Woodruff
(34).
keys (9) from both shift fingers (10 and 11 Remove
rocker shaft (6).
KEY to fig. 14-3.
42.
Retaining ring
1. Bearing cap
43.
Spacer
2. Gasket
44.
Bearing
3. Nut
45.
Shim
4. Bearing
46.
Fill plug
5. Drive gear
47.
Gear
6. Screw (2)
48.
Mainshaft
7. Throw out yoke
49.
Bushing
8. Shaft
50.
Pin
9. Clutch housing
51.
Gear and bushing assembly
10. Cover plate
52.
Washer
11. Lockwasher (2)
53.
Retaining ring
12. Capscrew (2)
54.
Synchronizer assembly
13. Bushing (4)
55.
Thrust washer
14. Shaft
56.
Gear and bushing assembly
15. Gasket
57.
Washer
16. Stud (41
58.
Bushing
17. Lockwasher (4)
59.
Pin
18. Nut (4)
60.
Gear and bushing assembly
19. Cover plate
61.
Washer
20. Gasket
62.
Retaining ring
21. Gasket
63.
Synchronizer assembly
22. Thrust washer
64.
Bearing
23. Bearing
65.
Welch plug
24. Bearing spacer
66.
Retaining ring
25. Bearing
67.
Bearing
26. Idler gear
68.
Spacer
27. Thrust washer
69.
Retaining ring
28. Idler shaft
70.
Gear
29. Lock plate
71.
Spacer
30. Screw and washer
72.
Gear
assembly
73.
Gear
31. Cotter pin
74.
Woodruff key (3)
32. Nut
75.
Countershaft
33. Washer
76.
Transmission housing
34. Gear
77.
Pipe plug
35. Oil seal
78.
Gasket
36. Capscrew (6)
79.
Cover plate
37. Bearing
80.
Screw and washer assembly (12)
38. Washer (61
81.
Bearing
39. Bearing cap
82.
Spacer
40. Gasket
83.
Nut
41. Bearing cup
14-4
TM 5-3810-294-34
