INTRODUCTION
SECTION I
SWING: Swing is defined as the function of rotating the
with dry threads. The use of thread lubricant or plated
upper of the machine.
threads will substantially lower the torque values required.
BOOM HOIST: The process of raising and lowering the
LIQUID CAPACITIES: Table 1-2 provides a listing of the
boom.
liquid capacities for machine components. The capacities
PROPEL: The process of moving the machine forward, re-
are also given in the lubrication charts provided in Section
verse, left or right.
TABULATED DATA
METRIC CONVERSIONS: Use Table 1-3 to convert the
English units in this manual to metric units.
TORQUE VALUES: Unless otherwise specified, torque all
common bolts and screws on this machine to the values
GENERAL DIMENSIONS: Figure 1-4 gives the dimensions
shown in Table 1-1. The torques provided are to be used
commonly required for machine shipping and erection.
Table 1-1. Recommended Torque Values
in Foot-Pounds (Dry Threads)*
Table 1-2. Liquid Capacity Chart
IDENTlFlCATION
U.S.
METRIC
Screw, Stud
or Bolt
Cooling System
5.75 Gal.
21.8 Liters
Diameter (in)
Detroit Diesel 4-71 T
Coarse
Crankcase with Filter
20 Qts.
18.9 Liters
Threads UNC
Grade 5
Grade 8
Fuel Tank
289.6 Liters
76.5 Gal.
1/4-20
6
9
5/16-18
12-14
Battery
17-19
500 oz.
14.8 Liters
3/8-16
22-24
31-34
Propel Pump Transmission
2.3 Gal.
8.7 Liters
7/16-14
36-39
50-55
1/2-13
Gear and Chain Case
54-59
76-84
7.0 Gal.
26.5 Liters
9/16-12
77-85
110-120
Torque Converter Reservoir
17.0 Gal.
64.3 Liters
5/8-11
107-118
153-166
Hydraulic Reservoir (Propel)
3/4-10
190-210
270-292
(Control)
7/8-9
22.0 Gal.
83.3 Liters
280-310
437-475
1-8
425-460
650-710
Propel Gear Case
2.4 Gal.
9.1 Liters
1-1/8-7
570-620
930-1000
Throttle Reservoir
1-1/4-7
12 Oz.
0.355 Liters
810-870
1310-1410
1-3/8-6
1060-1140
1730-1850
1-1/2-6
1410-1510
2290-2460
Fine
Grade 5
Grade 8
Threads UNF
1/4-28
7
10-11
5/16-24
14-16
20-22
3/8-24
25-28
35-39
7/16-20
39-43
55-61
1/2-20
63-69
86-94
9/16-18
87-95
123-134
5/8-18
126-138
171-187
3/4-16
213-233
300-328
7/8-14
312-338
480-520
1-12
466-504
715-770
1-1/8-12
640-695
1040-1120
1-1/4-12
900-960
1460-1560
1-3/8-12
1210-1300
1970-2100
1-1/2-12
1585-1700
2570-2750
* Torque values are based on using plated hardware if lu-
bricants are used. torque will vary.
P159
