(2) Remove nuts (2) and lock washers (3). Lift
13-34.
Reassembly and Installation
straps (4) and (5) from bracket (31) and remove strips
a. Refer to figure 13-12 and assemble and install the
(6) and (7).
fuel tank assembly as described.
(3) With a suitable lifting device, remove fuel tank
(1) Install strips (32) and bracket (31). Place
(8) from brackets.
bracket (31) in position and secure with lock washer
(4) Remove capscrews (9), lock washers (10),
(30) and capscrew (29).
guard (11) and washers (12) from the fuel tank.
(2)
Place clamp (28) on tube (27) and secure in
(5) Remove capscrews (13), lock washers (14)
place with nut (26), lock washer (25) and screw (24).
and guard (15).
(3)
Assemble filter screen (23) and filler cap (22)
(6) Remove valves (16) and (17).
to fuel tank (8).
(7) Remove screws (18) and lock washers (19).
(4)
Install new gasket (21). Place transmitter (20)
Lift transmitter (20) out of fuel tank (8). Remove
in fuel tank and secure with lock washer (19) and screw
and discard gasket (21).
(18).
(8) Remove filler cap (22) and filter screen (23).
(5)
Install valves (17) and (16). Position guard (15)
(9) Remove screw (24), lock washer (25) and nut
on tank and secure with lock washers (14) and
(26). Lift tube (27) from tank (8) and remove clamp
capscrews (13).
(28).
(6)
Place flat washers (12) and guard (11) on tank,
(10) Remove capscrews (29) and lock washers
secure with lock washers (10) and capscrews (9).
(30).
(7)
Using a suitable lifting device, position fuel
Remove bracket (31) and lift strips (32) from bracket.
tank (8) in bracket (31).
13-32. Cleaning
(8)
Install strips (6) and (7) on straps (4) and (5).
a.
Clean all metal parts with cleaning solvent,
Place straps (4) and (5) on bracket (31) and secure with
Federal Specification P-D-680, or equivalent. Dry com
lock washers (3) and nuts (2).
pletely with compressed air.
(9)
Install pipe plug (1).
b. Clean filter screen by back flushing.
b. Refer to figure 13-11 and assemble the fuel lines
c. Discard all gaskets.
and fittings as follows.
d. Remove all sludge, deposits and water.
(1)
Install lock washers (30) and capscrews (29).
(2)
Install elbow (28) and place hose (27) in posi-
13-33. Inspection and Repair
tion. Tighten couplings (25) and (26).
a. Inspect the fuel tank for cracks, breaks or leaks. If
(3)
Install elbow (24), pipe tee (23), bushing (22),
any defects are located, clean tank with live steam and
adapter (21), and hose (20). Tighten nuts (19).
weld after all fumes are removed.
(4) Install elbow (18) and hose (17). Tighten coup-
WARNING
ling (16).
Steam clean fuel tank thoroughly before
(5)
Install pipe tee (11), reducer (12), check valve
welding. Leave all openings uncovered during
(13), and adapter (14). Tighten coupling (15).
welding. Refer to TM 9-237 for safety precau-
(6)
Install bushing (10), elbow (9), adapter (8), and
tions for welding containers that have held
hose (7). Tighten couplings (6).
combustibles.
(7)
Install elbows (5) and (4) and hose (3). Tighten
b. Inspect all parts for thread damage or defects.
couplings (1) and (2).
Replace as required.
(8)
Check all connections for fuel leaks.
13-35.
Description
The radiator assembly is made up of a water cooling
radiator, oil cooler, hydraulic controlled fan, and radia-
tor shroud. Coolant is circulated from the water pump
to the radiator where it is cooled, and then recirculated
through the cooling system.
13-36. Removal and Disassembly
a. Remove carrier radiator as follows:
13-25
